After Setting Up Go Spas Hot Tub Will It Repeat the Cycle and Start Again?
Helpful Links
Operational & Technical Issues
Why is my spa overheating?
If the spa is located in an area that is experiencing hot weather, it is normal to have the spa h2o temperature rising.
To assist keep your spa cooler, adapt the spa'due south filtration cycles to no more than three hours per day, and merely one hour per day during the warmer summertime months. Set the cycles to run during later evening or early morning hours when the outside air temperature is cooler. During the summer, set simply one filter cycle per day.
Open the cover for several minutes, long enough to permit the water to cool downwards. Repeat a couple times weekly equally necessary. For condom reasons, never leave your spa unattended with the embrace open.
If OHH is displayed on the control panel, this means that the thermometer has detected spa water temperature above 110 degrees F. Do not employ the spa at this temperature. Take the brash steps above to cool your spa water to below 106 degrees F before use.
Why won't my spa heat?
If your spa temperature is low, outset check the thermostat to meet if it has been turned downward or ready to depression heat range. Adjust the thermostat to desired temperature or set to loftier heat range.
Another common reason for your spa temperature to exist low is considering the loftier limit sensor has tripped. Printing any button on your command console to reset the organisation.
If neither of the above steps works, your heating organisation may be lacking. Contact your authorized Bullfrog Spas Dealer for farther diagnosis.
Why is my GFCI breaker tripping?
Warning: You must be a qualitied electrician and or service technician to perform diagnosing or series injury or death can result: Loftier voltage components are in use.
If the spa was recently installed, the most mutual reason the GFCI would trip is the Load Neutral (white wire) between the spa and GFCI which must be connected to the Load Neutral port in the GFCI breaker. If the neutral wire is connected to the neutral busbar, the breaker will trip during startup. The neutral connection must non take contact to the basis on the load side of the breaker or it volition trip.
If the spa is not tripping immediately upon startup, a process of elimination should be used to identify the problem. Disconnect i component at a time from the control board and try restarting the spa. If the breaker trips, reconnect the component so attempt over again past disconnecting a dissimilar component. Continue repeating this process until the breaker does non trip. Components include pumps, heaters, lights, stereos, ozone, etc. If the breaker does non trip after disconnecting the component, then the disconnected component is the source of the trouble. Once you have determined which component is at fault, replace the component.
If y'all accept not establish the source of the problem after disconnecting each spa component individually, disconnect all components from the control board and try starting the spa. If the breaker still trips, a certified electrician will need to audit the billow and wiring.
Why is my spa making a vibration noise?
A light vibration noise is normal while the spa pumps and motors are running.
If your spa'southward vibration racket level seems excessive, the first thing to bank check for is the spa motor's shipping bolts. Each spa motor has a aircraft bolt that can contribute to the vibrating noise and can be removed once your spa is delivered and installed. The bolts accept tags with cherry lettering for like shooting fish in a barrel identification.
If the bolts take been removed and your spa notwithstanding makes an excessive vibration noise, contact your spa dealer for farther assistance.
Why is my spa pump creating a called-for odour or making excessive noise?
If your spa pump is creating a called-for smell or making excessive racket, the pump motor is defective. This can happen when running the pump during high ambient outside temperatures or due to excessive run times. Please contact your authorized Bullfrog Spas dealer for replacing the pump.
Why are my control pad and spa equipment non operating?
If your hot tub command pad and spa equipment are not operating, that means you have no electrical ability to the spa. Turn on or reset the GFCI circuit breaker to supply the spa with power again. If this does not solve the trouble, have a qualified Electrician bank check the electrical service for issues.
Another reason your control pad and equipment won't work is if the fuse (twenty or 30A depending on the system) has blown. Contact your authorized Bullfrog Spas Dealer for repair/replacement.
Why are my hot tub jets not working?
If your hot tub jets are s urg ing on and off , the first thing to check is your water level as it might be also depression. Accommodate h2o to the h2o level indication marker on the faceplate of the filter assembly.
Adjacent, check your filters as they may be muddied. If so, make clean or replace them .
If your spa'due south jets seem weak or are not working, get-go double-check to make sure that the valves are open up. JetPaks have valves at the bottom that open and close past turning the valve . Adjustable jets on K Series, A Series, R Serial, and STIL spas open and close past turning the jet face. Adaptable jets on X Series spas open and shut by turning the outer ring.
The next matter to check is the suction plumbing equipment(southward) normally located at the lesser of your spa shell to encounter if they are blocked. Remove any debris you discover by mitt or with a spa vacuum.
If your jets are not working later filling your spa, you most likely have an airlock in the pump. Follow the directions in the "how do I fix an airlock in the pump" section beneath.
Why won't my spa won't work after draining and refilling it?
If your spa pumps/jets are not working subsequently filling your spa, you virtually likely have an airlock in the pumps. Follow the directions in the "how do I fix an airlock in the pump" section below.
How do I gear up an airlock in the pump?
To forbid airlocks when filling your spa, be sure to open all valves in the JetPaks and all other jets in the spa before filling to allow as much air every bit possible to escape from the system during the filling process. Fill your spa through the filter past taking the filter cap off and put the hose directly in the filter. Detailed instructions for filling each spa series are constitute in your owner's manual.
Your hot tub'due south pumps must be primed directly afterwards filling to ensure correct functioning of your spa and get rid of any airlocks. Subsequently initial startup, verify that the home status screen appears on the panel.
Depending on your spa model, your spa has either 1,two, or three pumps. To prime the pumps, press the "Jets i" push button one time to prime in low-speed. Subsequently the pump turns on and h2o is visibly flowing from the jets wait a few seconds and then press "Jets 1" again to initiate highspeed functioning of Pump i. The pump has primed when h2o is flowing from the jets.
If your spa is equipped with a 2nd jet pump, echo the priming process for Pump 2 past pressing the "Jets 2" push button once to turn on low speed and and then a 2d time to turn Pump ii on loftier.
If your spa has a 3rd pump, printing the "Jets 3" button to prime the tertiary jet pump. All pumps will have primed when water is observed flowing from the jets associated with each pump.
On rare occasions, priming the pumps volition not get rid of an airlock. The side by side step is to remove the front panel and locate the pump with an airlock. The wet-terminate of the pump has a drain valve—loosen this until all the air escapes and h2o starts to drip out, or loosen the union on the pump to permit the air out until you see water. Practice non attempt this while the spa pump is running. If you need assistance doing this or this does non resolve the trouble, delight contact your authorized Bullfrog Spa Dealer.
Why do my spa jets turn off during operation?
If your jets turn off automatically after either 30 or 60 minutes, this is completely normal. The automatic timer has completed its cycle. Simply turn the pump back on to start a new cycle.
Some other reason your jets can turn off unexpectedly is if the pump has overheated due to the vents on the equipment door being blocked. Clear away whatever items from the vents and wait a while to see if your jets work again.
The last reason your spa jets can plough off is if the pump motor is lacking. In this example, contact your authorized Bullfrog Spas dealer for service.
Why are my hot tub jets/pump not turning off?
If you are trying to turn off the pump for jets 1 on your spa and it appears that they are not turning off, your spa is in the heart of a filtration cycle. Spas not equipped with a dedicated filtration pump will turn on automatically, using jet pump 1 on depression speed, to filter and/or heat. This is normal spa operation.
What do I practise if my spa is leaking?
If you notice your spa is losing water, cheque all fittings and equipment in the equipment compartment for the source of leakage. If a leak is detected, tighten the fitting by hand. If the leak persists, you cannot find the source of the leak, or the leak is coming from the shell, contact your authorized Bullfrog Spas Dealer.
Water Quality Issues
How do I become rid of green water in my hot tub?
The first reason why your hot tub can turn green is from algae growing in the spa. This happens because of a lack of sanitizer (chlorine or bromine). Super sanitize (shock) the spa water to get rid of algae and other growth in the spa.
If the spa h2o has had algae growing for as well long of a time, shocking the spa water may not be enough. At that betoken, yous would desire to drain your spa, give information technology a good cleaning, and refill your spa. Be sure to properly maintain your spa pH and sanitizer levels going forrad to preclude time to come algae growth.
A 2d reason why hot tub h2o can announced green is from metals and minerals in the water (usually copper). Check with your spa dealer virtually local h2o conditions to see if your area has copper in the basis water. If this is the case, your dealer volition be able to provide custom tips for keeping your spa water clean and clear.
How do I become rid of mold in my hot tub?
Mold, mildew, and mucus like to grow in warm, clammy places. The starting time step in preventing these from growing in your spa is to maintain your spa water. You should add together sanitizer following every utilize.
It's besides important to regularly clean all surfaces on and around your spa, including the cover (the underside and the summit), cup holders, headrests, etc. We recommend cleaning those surfaces every 30-45 days.
Why is my spa h2o cloudy?
Cloudy spa water is usually caused by non-filterable liquid waste (east.g. perspiration) and a lack of proper maintenance. First, bank check your spa'south pH level and adapt if needed. High pH levels are a mutual crusade cloudy water.
Next, examination your sanitizer (chlorine or bromine) levels. If the sanitizer level is likewise low, add more. Look two hours and test the water again. Add more than sanitizer as necessary then wait two more than hours. Repeat this process until the sanitizer levels consistently read correctly. E'er run the pumps for 15 minutes with the cover open after calculation any chemicals.
If y'all are using the FROG @ease for Bullfrog Spas water intendance system, start make certain the SmartChlor cartridge is non empty. Replace the cartridge if necessary. If it is not empty, turn the dial setting up 1 number and monitor chlorine levels for a few days while maintaining water residuum. If needed, turn the dial up again. The entire FROG @ease Organisation including a FROG @ease Mineral Cartridge needs to be replaced every four months. Without the minerals, SmartChlor will non be enough to sanitize the hot tub.
If your sanitizer levels are generally testing at correct levels and your spa water is still cloudy, you can increase filtration times to run into if that helps.
You may also want to clean or supercede the filters if y'all take not done then recently.
Non-filterable micro-particulate waste material (e.g. grit) can too contaminate the water leading to cloudy water. To remove these substances, use a water clarifier production as per the manufacturer's instructions.
How practise I go rid of foam/bubbles in my hot tub?
People and their swimwear innovate most of the unwanted contaminants that cause foam and bubbling in a hot tub. To reduce the amount of foam and contaminants introduced to your spa water:
- Equally much equally possible, avoid entering your spa with sunscreen, lotions, deodorants, shampoos, or like substances on your body, or detergents on your clothes.
- Do non wash swimwear you intend to wear in your spa with detergents. Many people proceed a dedicated "spa" suit that is never laundered with detergent but simply rinsed well afterward use.
- Rinse off in the shower before (and after) spa employ.
For a temporary set up for foam and bubbling in your spa, add an anti-foam or foam remover as per the manufacturer's instructions. This will get rid of the foam almost immediately but will simply be temporary, lasting a day or ii.
The all-time manner to command foam is to super sanitize (shock) the water. This volition destroy the soap agents that normal levels of sanitizer volition not. Make sure to properly maintain your spa pH and sanitizer levels and avoid introducing the unwanted contaminants listed above to foreclose future foam and bubbles.
How exercise I foreclose a yellow h2o line from edifice in my spa?
With normal use of the spa, oils, lotions, and hair products tin can build up on the surface of the water in small amounts. This could leave a yellow water line effectually the perimeter. This buildup can be easily removed using a spa surface cleaner or its equivalent. Avoid using cleaning agents that leave soap residual in the water.
Alert: Never allow your spa surface to be exposed to booze, acetone (boom shine remover), nail polish, dry out cleaning solution, lacquer thinners, gasoline, pine oil, abrasive cleaners, or whatever other household chemicals other than those listed. These chemicals void the warranty.
What do I do if my peel is sensitive to hot tub chemicals?
If your peel is sensitive to hot tub chemicals, make sure to rinse off after you become out of the spa. Using lotions to moisturize your skin tin too help.
Information technology'southward also important to making sure the pH and sanitizer levels are correct in your hot tub. Low pH levels (less than 7.4) tin cause discomfort to your peel and likewise as corrosion to the spa equipment. To increase pH levels, add a pH increaser.
If your sanitizer levels are correct and you still experience discomfort, attempt switching to a different sanitizing amanuensis—If you are using chlorine, endeavour bromine, and vice versa.
Your dealer may have boosted tips based on the chemical makeup of your local water supply. Whatsoever allergic reactions should be treated past a medical professional person.
How do I get rid of debris in my spa h2o?
Debris from wind, trees, and users volition occasionally accumulate on the bottom of the spa. The filtration system will remove the smaller debris. Large or heavy debris can exist removed with a hand-held spa vacuum available at your Bullfrog Spas dealer.
Hot Tub Parts & Accessories
Where do I find replacement parts and accessories for my hot tub?
If you lot are in need of replacement parts or accessories for your Bullfrog Spa, starting time achieve out to your local dealer.
Additionally, some products are available online at shop.bullfrogspas.com
Why are my spa headrests disintegrating?
Headrest discoloration and/or deposition is accelerated by loftier sanitizer use and improper ventilation after shock treatments. To foreclose your spa headrests from disintegrating, remove the them during and after shock treating the spa water or when sanitizer levels are high. In addition, leave your spa comprehend open for at least 30 minutes after shocking to ensure the headrests are non affected.
It'due south likewise a good thought to open the embrace for simply a few minutes a couple times a week even if your spa is not existence used or lightly used so that the excess chemic gasses building up under the comprehend can escape.
Nosotros too recommend regularly cleaning all pillows with mild soap, water, and a make clean cloth. Monthly, treat the pillows using a not-petroleum-based production such as 303 Protectant. This will maintain water resistance and luster of the product.
How do I supercede my hot tub cover clips?
Broken clips are from potent winds or failure to undo them before opening the cover and is not a warranty office.
Contact your dealer to get replacement clips or buy them from our online shop.
To replace the comprehend clip, first remove the male stop of the clip. And so, utilize clippers to make 2 small diagonal cuts on the clip loop. This makes an opening for the cover loop. Insert the comprehend loop into the opening and push the cover loop entirely into the clip.
Why tin can't I get a wifi signal on my hot tub?
If you can't get a wifi signal on your Bullfrog Spa, first ensure that both the main and partner units are correctly installed. The primary unit should be connected to the spa's command board and the partner unit of measurement to the wifi router. If at that place is a solid blue light on both units, and so the connection is present. If one or both of the units does not have a low-cal, or the light is flashing, refer to the Gecko wifi troubleshooting website.
Why tin't I get a bluetooth bespeak on my hot tub?
First, make certain the in.stream2 unit is turned on from the topside control panel.
Next, effort adjusting the stereo settings to zero (or to eye).
If at that place is no power coming from the motherboard, the command box will need to be replaced.
If there is power coming from the motherboard merely the in.stream2 volition not plow on, the in.stream2 unit of measurement will need to be replaced.
Control Panel Error Code Questions
My spa has a Freeze Mode error code, what do I practise?
Your spa is equipped with a freeze protection mode. When potentially freezing exterior temperatures are detected, your control system will turn on to check the water temperature. If heating is necessary to protect your spa from freezing weather condition, your spa may turn on and heat to a safe temperature. A notification will display on the primary command screen indicating this mode is engaged. If your spa shows this error code for more than 24 hours, contact your dealer for further diagnosis.
My spa has a Low Menstruum / Heater Overheating error code, what practice I practise?
First, remove the filters and try running the spa without them. Make sure the area is clear of debris. Turn the pumps on and off several times each to endeavour purging out any airlocks in the pumps.
Side by side, check for blockage in the pumps. To do and so, plough the spa off and drain the spa. Disconnect the intake side of the pump and check within for blockages. Spa accessories such as a scumball, leaves, or other debris tin can be sucked into the pumps and need to be cleared away.
To ameliorate prevent future blockages, make sure you are using genuine Bullfrog Spas filters every bit other filters may non forestall debris from entering the pumps.
If the water flow is good and there is nevertheless a flow status code, the sensors on the heater should be tested. The heater may need to exist replaced due to a bad sensor. If the upshot still persists, the excursion board will need to exist replaced.
If the spa is new, bank check to ensure the ability cord is connected properly. In addition, check the power connections to the pump. Finally, check the control prepare for proper functioning (refer to dealer).
What does filtration suspended mean?
This code does not indicate an error, information technology indicates that the spa filtration wheel has been suspended considering a user activated the spa while it was performing a filtration cycle. No further activeness is required. The next regularly scheduled filtration cycle will occur.
What is a purge menstruation?
In order to maintain sanitary weather and protect against freezing, your spas pumps volition purge h2o from their respective plumbing by running all pumps at the beginning of each filter cycle.
The filtration schedule shown on the screen will use to the main filtration pump. If your spa uses a circulation pump configured to run 24 hours, the screen will show y'all the purge setting instead of filtration. The purges are pre-programmed for a stock-still number of minutes; therefore, the duration will be ready to Northward/A on the screen, and just the start fourth dimension can be modified.
Other Oft Asked Questions
What do I do if I won't be using my hot tub for a long menses or during vacation?
two-6 weeks of unuse
If the spa will not be used for at least ii weeks, lower the temperature to the lowest setting of lxxx F (26°C) or identify in low range oestrus mode. Lowering the temperature will cut the toll of performance; however, you will need to adjust the temperature setting approximately 4 hours before use in gild to oestrus the spa to 100 F (38°C).
Fifty-fifty though you will not be using the spa, be certain to maintain the spa water and frequently check that the spa is performance correctly. Failure to practise and so could lead to corrosion, staining, or scaling to the spa and its equipment.
During periods of freezing temperatures, a spa that has malfunctioned may exist subject area to damaged plumbing or equipment as a result of ice buildup within the spa. If the spa cannot exist checked and maintained on a weekly footing, and so consider winterizing the spa.
More 6 weeks of unuse
When you are not planning to use the spa for half dozen or more weeks, or when someone is not able to maintain the spa on a weekly ground, yous should use Away mode. For extended absences you may also choose to winterize the spa.
How do I winterize my hot tub?
Bullfrog Spas are designed to function well, stay warm, and concur up through the coldest of weather and do non crave winterization unless you will be leaving your spa unattended for 6 or more weeks.
Either mode, we recommend to check-in on your spa weekly during winter months to assist forbid freeze harm.
To winterize your Bullfrog Spa, follow the detailed instructions in this article:
https://world wide web.bullfrogspas.com/weblog/how-to-winterize-a-hot-tub/
Tin I fill up a spa in freezing winter temperatures?
If your spa is being delivered during the winter or you lot demand to drain and refill your spa during freezing temperatures, y'all may be wondering if the cold weather mean you can't fill your spa with h2o.
Luckily, you can fill your spa in freezing wintertime temperatures. To keep your spa components safe from the cold, but turn your spa on as shortly equally it is full so the heater and pumps keep everything from freezing.
Sometimes, your dealer may postpone delivery of your spa during winter storms because it can exist dangerous for them to deliver a heavy spa with snow, rain, or ice on the ground. One time it is safe again, they will deliver your spa and can assist you fill up it up and get it started.
If you don't programme on using your spa during the winter, follow this guide on winterizing your hot tub. Yet, using a hot tub in the winter is considered the most enjoyable time by many spa owners.
What practice I exercise when my spa loses power in freezing temperatures?
If your Bullfrog Spa loses power during freezing temperatures either due to a power outage or a malfunction and the GFCI won't reset, you volition want to assistance go on the spa and its components warm until power is restored or your dealer can repair the malfunction.
Do non drain your spa. Leave your cover on to retain as much heat as possible.
Remove the access panel to your spa and identify a minor space heater within the cabinet on a depression setting. This volition help continue the pumps and pipes warm. You lot can also identify a blanket over the equipment area to assistance keep everything insulated.
Oft monitor the spa until ability is restored and your spa is functioning once again.
How do I movement my spa?
A cart or dolly that tin can back up at least 900 pounds is the best fashion to move your spa. Slip sheets or carpets can also be used to drag a spa on well-nigh surfaces.
Spas can be moved in the horizontal or vertical position, simply practise non lift the spa on the door side because the door side cannot support the weight of the spa and you may break the door.
Be conscientious of common obstacles in your path such equally overhanging tree limbs, awnings, protruding gas meters, water meters, and A/C units.
Which filter cycle (water care functioning style) should I use for my spa?
*The following data is for Bullfrog Spas model years 2019 and newer. Please refer to possessor's manual for your spa for the most authentic information.
The best filter bike for your situation volition depend on how oftentimes you use the spa and what time of day you lot typically utilize the spa. The two most mutual modes are Standard-beginner and Super Free energy Savings. The factory default setting is Super Energy Saver style.
In the descriptions of each mode below, "economy fashion" means that the fix point volition be reduced past 20°F* (xi°C), which means that the heating system will not exist engaged unless the temperature falls to 20°F (11°C) below the spa'southward set temperature. The filtration schedule shown on the screen will employ to the main filtration pump. If your spa uses a circulation pump configured to run 24 hours, the screen will show you the purge setting instead of filtration. The purges are pre-programmed for a fixed number of minutes; therefore, the elapsing will exist set to N/A on the screen, and only the start time can exist modified.
Abroad
In Away mode, the spa temperature gear up point will be reduced by xx°F (11°C) (see description of "Economic system mode" above). Spa will remain in Economy style at all times of the twenty-four hours and all days of the week.
Suggested utilise: Utilise when on holiday or not using the spa for longer than 2 weeks.
Economy time: Every mean solar day of the week, 24 hours per twenty-four hour period.
Filter bicycle beginning time: 8:00 PM, duration 3 hours.
Standard-beginner
In Standard manner, the spa will estrus to the set bespeak and filter co-ordinate to the spa's standard configuration. Spa will heat to set point at all times and all days of the week. This is the default setting on new spas.
Suggested use: Use to maintain readiness for employ every day at all times of twenty-four hours.
Economy time: Will not utilise Economic system mode.
Filter cycle outset times: 8:00 AM, duration 1.v hours and 8:00 PM, duration one.five hours.
Energy Savings
In Energy Savings mode, the spa temperature set point will be reduced by 20°F (11°C) (see description of "Economy way" above) during tiptop daytime hours. Spa volition heat to normal fix point during evening hours and on the weekend.
Suggested use: Use to save energy during weekday daytime hours and make ready for use at night and all day on weekends.
Economic system time: Monday – Friday, 6:00 AM – half dozen:00 PM.
Filter bicycle start time: seven:00 PM, duration 3 hours.
Super Energy Savings (factory default setting)
In Super Energy Savings style, the spa temperature ready point will be reduced by 20°F (11°C) (come across description of "Economic system manner" to a higher place) during superlative daytime hours. Spa will rut to normal set point during evening hours, every day of the week.
Suggested apply: Use to save maximum energy and heat only during set filter cycles.
Economy time: Will not utilize Economy manner, only heats during filtration cycles.
Filter bike start time: viii:00 AM, duration i.v hours and 8:00 PM, duration ane.five hours.
Weekender
In Weekender manner, the spa temperature set bespeak will exist reduced by twenty°F (11°C) (see clarification of "Economic system mode" above) from Monday to Friday. Spa will heat to prepare point at all times on the weekend (Saturday & Lord's day).
Suggested use: Use when spa is used merely on weekends and not on weekdays.
Economy time: Monday – Friday, 24 hours per day.
Filter bike kickoff time: 8:00 AM, duration i.5 hours and 8:00 PM, duration 1.5 hours.
Default Settings: The Default Settings option will restore all Water Care modes and schedules to the spa's default settings. Y'all volition exist asked to confirm your choice.
NOTE: Spas NOT equipped with a defended filtration pump will plough on automatically, using jet pump 1 on depression speed, to filter and/or heat. This is normal spa functioning.
How practice I drain my spa?
Pace ane: Turn-off the main electrical billow to spa.
Step 2: Locate the drain below the equipment compartment door.
Step 3: Pull the drain out with a slight clockwise plow. Utilise pliers if needed. The drain is fully extended at approximately 2 inches (five centimeters).
Step 4: Remove drain cap. The drain spout will not bleed when fully extended.
Step five: Adhere a standard garden hose. Push the drain spout in halfway to activate the drain. The Spa will drain most five gallons (20 liters) per infinitesimal. Ensure that the drainage is in an expanse safely abroad from window wells or basement entries.
Step half-dozen: Once the spa is fully drained, pull the drain spout out all the style, remove the hose, supplant the bleed cap, and push the drain in all the manner.
How do I remove and replace my spa equipment door?
M Series Door Removal
Pace ane: Remove trim strips from trim channels by pulling carefully and firmly, working from the lesser of the trim strip to the top. Place trim strips bated.
Footstep two: Remove door – Carefully pull lesser of door out toward you. Advisedly grab the bottom corner of the door and pull information technology out enough that you tin can slip your other paw in behind the side of the door near 4-5 inches (10-thirteen cm) upwardly from the lesser. From in that location yous volition pull the door firmly abroad from the spa until the snap on the door pulls out of the snap feature in the rib. Continue to pull the door abroad until the second snap on the other side pulls out. The door tin can and so be dropped out of the groove on top and removed from the spa.
Step iii: Electrical Disconnect – be certain to disconnect any lighting or whatever other electrical wiring that is mounted onto the door before completely removing it.
Step four: When removed, lean door against spa. To reinstall spa door, reverse the instructions above.
M Series Door Installation
Step 1: Electrical – Reconnect any lighting or electrical devices on the door before installing.
Footstep ii: Door – Slip the upper lip of the door into the top backside the lip of the spa. Lower the door while gently pushing on it until y'all feel the snaps line up with the snap features in the ribs. Starting from one side, strength the first snap into place and then forcefulness the other side until the door is secured.
Step iii: Replace trim strips past snapping each carefully into the trim channel
STIL Door Removal
STIL spas are designed then that there are no visible fasteners from the exterior. Snap features in the corners and the chiffonier panels allow for simple equipment expanse admission, however, it is important to follow these recommended door removal instructions to avoid damaging the door or corner panels.
Pace one: Remove Corners – It is important to remove the front two corners overlapping the door before attempting to remove the door itself. This is done past placing a curt flathead screwdriver below the corner and slipping information technology up partway backside the corner and using it equally a lever to pry out the bottom half of the corner outward. In one case this is done, grab the corner by the bottom and pull it directly out allowing the top snap to come up gratuitous. Pull corner down and out of the groove on the top.
Step two: Remove Door – Once both front corners are removed, look on each side of the front end door to encounter the snap feature built into the cabinet. To remove the door, start by placing a longer flathead screwdriver or short pry bar into the center of the snap feature and use it every bit a lever to popular the door out of the first snap. Grab the base of the door and carefully begin pulling information technology out such that the rest of the snaps come free ane by one across the length of the door. The door tin can then be dropped out of the groove on tiptop and removed from the spa.
Step iii: Electrical Disconnect – exist sure to disconnect whatever lighting or any other electrical wiring that is mounted onto the door before completely removing it.
STIL Door Installation
Step 1: Electrical –Reconnect whatever lighting or electrical devices on the door earlier installing.
Pace 2: Door – Slip the upper lip of the door into the superlative groove of the extrusion. Lower the door while gently pushing on it until you experience the snaps line up with the snap features in the ribs. Starting from one side, force the first snap into place. Continue downward the length of the door and forcefully push the chiffonier into each of the snaps until the door is completely in and secured. Y'all tin feel along the lesser to make sure all are in identify and no gaps are present.
Step 3: Corner – Slip the upper lip of the corner into the superlative groove of the spa. Starting from the top force the starting time snap into identify, if the corner has slipped downwards and is not flush with the top groove this is the best time to button it support into place. Continue downwardly the length of the corner and forcefully push button it into each of the snaps until the corner is completely secured. The corner should fit tightly against the cabinet on both sides.
A, R, & X Series Door Removal
Footstep i: Remove trim strips from trim channels past pulling carefully and firmly, working from the bottom of the trim strip to the acme. Identify trim strips aside.
Stride 2: Remove door – Advisedly pull bottom of door out toward you. Carefully take hold of the bottom corner of the door and pull it out plenty that y'all tin can slip your other mitt in behind the side of the door near 4-v inches (10-13 cm) up from the bottom. From at that place you will pull the door firmly away from the spa until the snap on the door pulls out of the snap feature in the rib. Proceed to pull the door away until the second snap on the other side pulls out. The door can then be dropped out of the groove on pinnacle and removed from the spa.
Step 3: Electrical Disconnect – be certain to disconnect any lighting or any other electrical wiring that is mounted onto the door earlier completely removing it.
Pace 4: When removed, lean door against spa. To reinstall spa door, reverse the instructions above.
A, R, & X Serial Door Installation
Stride 1: Electrical – Reconnect whatsoever lighting or electrical devices on the door before installing.
Step 2: Door – Slip the upper lip of the door into the acme behind the lip of the spa. Lower the door while gently pushing on information technology until you feel the snaps line up with the snap features in the ribs. Starting from one side, force the showtime snap into identify and then strength the other side until the door is secured.
Step three: Replace trim strips by snapping each advisedly into the trim channel.
X6R Door Removal
Step 1: Remove trim strips from trim channels by pulling advisedly and firmly, working from the bottom of the trim strip to the top. Identify trim strips bated.
Step 2: Remove door – Pull the bottom of the door forwards, the door tin can and so be dropped out of the groove on elevation and removed from the spa.
Step iii: Electrical Disconnect – be certain to disconnect any lighting or any other electric wiring that is mounted onto the door before completely removing it.
Footstep 4: Afterwards the door has been completely removed, lean door against spa.
X6R Door Installation
Stride ane: Electrical –Reconnect any lighting or electric devices on the door before installing.
Step 2: Door – Sideslip the upper lip of the door behind the lip of the spa. Identify door deeply against spa flush with the side panels.
Step three: Replace trim strips past snapping each carefully into the trim aqueduct.
Additional Resources
Source: https://www.bullfrogspas.com/frequently-asked-questions/
Post a Comment for "After Setting Up Go Spas Hot Tub Will It Repeat the Cycle and Start Again?"